Drip Edge Flashing Repair Altadena CA that stops edge leaks cold
Licensed flashing work for Altadena homes, from the foothills down
Drip Edge Flashing Repair Altadena CA is the metal edge work that keeps wind-driven rain out of your fascia, sheathing and eaves. If you have seen rust streaks, peeling paint or water in the attic after a storm, we can help. We are Hometown Roof Protectors, a licensed C-39 roofing contractor serving Altadena and Los Angeles County since 2020, and we handle drip edge flashing repair in Altadena, California with same-week scheduling.
What Drip Edge Flashing Repair Altadena CA Actually Involves
Drip Edge Flashing Repair Altadena CA is roof-edge metal work that directs water away from the fascia, sheathing and foundation instead of letting it wick backward under the shingles. The drip edge sits along the rake and eave edges, lapped over the underlayment at the eaves and under it at the rakes. When that metal lifts, corrodes or loses its sealant, water finds the seam. We remove the failed section, inspect the decking beneath, then install new galvanized steel or aluminum with the correct 2-inch overlap and fasten it every 12 inches.
Altadena sits against the San Gabriel foothills, so roof edges here take wind from the canyons and afternoon sun that bakes the west-facing rakes. That combination dries out old butyl tape and roofing cement, cracks the sealant and lets water in during the first real storm. If you have been searching for a drip edge flashing repair near me in Altadena CA, we can usually get eyes on the roof within 24 to 48 hours. Most edge repairs take two to four hours and cost between $180 and $650 depending on how much metal has to come off.
Why Altadena Homeowners Fix Drip Edge Flashing Early
Small edge failures turn into fascia rot, attic stains and $2,000-plus repairs if you wait. Here is what a proper drip edge flashing fix in Altadena actually buys you.
Stop Water Before It Spreads
A lifted drip edge lets water run backward under the shingle course and into the sheathing. We reseal and refasten the edge so water sheds off the roof instead of soaking the deck. Catching it early keeps the repair in the $180 to $650 range instead of a full fascia and deck replacement.
Protect Fascia And Paint
Fascia boards behind a failed drip edge rot from the top down, and the paint peels in long strips. Replacing the metal and resealing the joint stops the cycle. We have seen Altadena homes where one winter of ignored edge leaks meant $1,400 in carpentry and repainting.
Handle Wind-Driven Foothill Rain
Altadena storms push rain sideways off the canyons, and that is exactly the angle a loose drip edge cannot handle. We fasten the new metal with roofing nails every 12 inches and seal the laps with polyurethane sealant rated for the temperature swings we get here.
Keep The Attic And Insulation Dry
Water that slips past the drip edge shows up as dark stains on the attic sheathing and soggy insulation within a season. Fixing the edge stops the source. We check the attic side of the eave on every job so you know whether the leak has already traveled.
How Our Drip Edge Flashing Repair Process Works
Five steps, one visit for most Altadena homes. Here is exactly what happens from the first call to the final water test.
Roof Edge Inspection
We walk the perimeter and check the rake and eave edges, looking for lifted metal, rust, cracked sealant and missing fasteners. On a typical Altadena ranch home that takes 20 to 30 minutes, and we photograph every problem spot so you see what we see.
Written Scope And Price
You get a clear price before we start. Most drip edge flashing repair in Altadena, California lands between $180 and $650, and we tell you which sections need replacement versus resealing so you are not paying for metal you do not need.
Removal And Deck Check
We pry up the failed metal with a flat pry bar, pull the old nails and inspect the decking underneath. If we find soft sheathing or rot, we tell you on the spot and quote the carpentry before we go further.
New Metal And Sealing
New galvanized steel or aluminum goes down with a 2-inch lap, fastened every 12 inches with roofing nails and sealed at the joints with polyurethane sealant. On rakes we tuck the metal under the underlayment; on eaves it goes over. That detail is where most leaks start.
Water Test And Cleanup
We run a hose test along the repaired edge for 10 to 15 minutes and check the attic side for moisture. Then we magnet-sweep the lawn and driveway for nails. You get photos of the finished work and a 5-year workmanship warranty on the repair.
Why Altadena Calls Us For Drip Edge Flashing Repair
We are a local roofing contractor, not a storm chaser. Here is what you get when you book a drip edge flashing fix in Altadena with us.
Same-Week Scheduling
Most drip edge repairs get on the calendar within 24 to 48 hours of your call. During storm season we hold slots open for emergency drip edge flashing fix Altadena requests, because a lifted edge during a rain event can flood a wall in hours.
Licensed And Insured Crews
We hold a California Contractor License (C-39 Roofing) and carry full liability and workers comp coverage. Every technician is OSHA safety certified and trained on NRCA flashing details. You are not letting an uninsured handyman on your roof.
Materials That Last In Foothill Weather
We stock galvanized steel, copper and aluminum drip edge, plus Henry and Grace underlayment products and Oatey sealants. For homes near Rubio Canyon and Winter Creek we often recommend copper or heavier-gauge aluminum because it handles the wind and sun exposure better than thin steel.
Photo Proof And A Written Warranty
You get before-and-after photos of every repaired section, plus a 5-year workmanship warranty on the flashing work. If the same edge leaks again, we come back and make it right. That is the difference between a quick patch and a real drip edge flashing repair and sealing Altadena CA job.
What Our Drip Edge Flashing Repair Includes
Every edge repair we do covers the metal, the fasteners, the sealant and the inspection. Here is what is standard on a Hometown Roof Protectors drip edge job in Altadena, and what we quote separately if we find it.
What's Included
Full Edge Inspection
We check every rake and eave edge, plus the attic side of the eave where water shows up first. You get a written summary of what is failing and what is still sound.
New Drip Edge Metal
Galvanized steel, aluminum or copper, cut to length with tin snips and a hand seamer, lapped 2 inches and fastened every 12 inches with roofing nails. We match the profile to your existing edge so it looks original.
Sealant And Underlayment Repair
We reseal laps with polyurethane sealant and repair torn underlayment with Grace or Henry products before the new metal goes down. Skipping this step is why most DIY edge fixes leak again within a year.
Fastener And Flashing Check
While we are up there we check step flashing, kickout flashing and vent pipe boots near the repaired edge. Loose counter flashing or a failed boot often shows up at the same time as a drip edge problem.
Water Test And Photo Report
A 10 to 15 minute hose test confirms the repair holds, and you get photos of the finished work plus a 5-year workmanship warranty. We also magnet-sweep for nails before we leave.
Roof Edge Problems We Fix In Altadena
Most drip edge failures look the same from the ground. Here are the ones we see most often on Altadena roofs, and what happens if they are left alone.
Lifted or bent drip edge after a windstorm
Water runs backward under the shingle course and soaks the sheathing and fascia. Left alone, that turns into rot and a $1,500-plus carpentry bill.
We pull the bent section, check the deck, and install new metal with proper laps and fasteners. Most repairs take two to three hours and run $180 to $450 for a single elevation.
Cracked sealant along the drip edge joint
Hairline cracks let water wick into the eave, which shows up as attic stains and peeling exterior paint within one rainy season.
We clean the joint, remove the old sealant, and reseal with polyurethane sealant rated for Altadena's temperature swings. This is the most common drip edge flashing fix we do, and it usually takes under two hours.
Rust streaks on the fascia below the edge
Rust means the metal has already lost its coating and is staining the fascia. The corrosion spreads and the edge stops shedding water entirely.
We replace the corroded section with galvanized steel or aluminum and treat the fascia if needed. On homes near the foothills we often recommend heavier-gauge metal that handles the sun and wind better.
Missing drip edge on an older Altadena home
Some pre-1980 homes were built without drip edge at all. Water runs straight down the fascia and into the foundation planting, and the sheathing edge stays wet.
We fabricate and install new drip edge on a flashing brake to match the roof profile, then seal and fasten it to code. This is a common fix on Christmas Tree Lane and Historic Highlands bungalows.
When To Book Drip Edge Flashing Repair In Altadena
You found water stains on the attic sheathing after the last storm near Rubio Canyon.
We inspect the eave edge and the attic side, then repair or replace the failed drip edge section and reseal the joint. We also check step flashing and kickout flashing while we are up there.
The leak source is sealed, and you have photos showing the dry sheathing after our water test.
Your fascia paint is peeling in long strips along the west-facing rake.
Peeling paint on the fascia almost always traces back to a drip edge that is not shedding water. We replace the metal, reseal the laps, and confirm water runs off the edge instead of behind it.
You can repaint the fascia knowing the water source is fixed, not just covered up.
A windstorm lifted the drip edge on your tile roof near Loma Alta.
Tile roofs need the edge metal tucked correctly under the tile course. We lift the affected tiles, replace the drip edge, and reset the tiles without breaking them.
The edge is fastened every 12 inches and the tile line is intact, so the next wind event does not repeat the damage.
You are selling your Altadena home and the inspection flagged the roof edge.
We do a full edge inspection, repair what is failing, and provide a written summary with photos that you can hand to the buyer or their agent.
The edge issue is documented and repaired, which keeps the sale moving instead of turning into a credit request.
Tools And Methods We Use On Drip Edge Repairs
Tools & Equipment
Flashing brake
Lets us fabricate custom drip edge profiles on site to match older Altadena roof lines that no longer match off-the-shelf metal.
Tin snips and hand seamer
Used to cut and fold galvanized steel, copper and aluminum cleanly so the laps sit flat and seal properly.
Roofing nailer
Drives fasteners at consistent depth every 12 inches along the edge, which is the spacing that keeps metal from lifting in wind.
Caulking gun and polyurethane sealant
Applies an even bead of sealant at every lap and joint. Polyurethane holds up to Altadena's temperature swings better than basic roofing cement.
Flat pry bar
Removes the failed drip edge and old nails without tearing the underlayment or damaging the shingle course above.
Seam roller
Presses butyl tape and self-adhered underlayment flat at the eave so water cannot tunnel under the new metal.
Methods & Techniques
NRCA flashing standards
We follow NRCA lap and fastening details on every edge repair. That means a 2-inch lap, fasteners every 12 inches, and correct underlayment placement at the eave and rake.
GAF Master Elite installation practices
As a GAF Master Elite contractor we install edge metal and underlayment to manufacturer spec, which keeps your roof system warranty intact after the repair.
Hose water testing
Every repaired edge gets a 10 to 15 minute hose test before we pack up. If water shows up on the attic side, we keep working until it does not.
Photo documentation
We photograph the failed edge, the deck condition and the finished repair. You get the images by text or email, which is useful for insurance claims and home sales.
How Drip Edge Flashing Repair Runs In Altadena
Altadena roofs sit against the San Gabriel foothills, and that shapes every edge repair we do here. Wind comes down the canyons hard enough to lift metal that was fastened too thin, and the afternoon sun on west-facing rakes dries out old sealant within a few seasons. The housing stock runs from 1920s bungalows near Christmas Tree Lane to mid-century ranches in East Altadena and newer builds around La Viña. Older homes often have wood fascia that has already been wet once or twice, so we check for soft wood before we install new metal. We also see a lot of missing kickout flashing on homes where a roof meets a wall, and that shows up as the same kind of water intrusion as a failed drip edge. If you need a drip edge flashing leak repair in Altadena, California, we can usually get out within 24 to 48 hours, and most jobs finish in a single visit. We serve ZIP codes 91001, 91003 and 91104, and we work with Los Angeles County code requirements on every edge detail.
Service Areas
Historic bungalows here often have original wood fascia and no drip edge at all. We fabricate new metal on a flashing brake to match the original roof profile.
Higher elevation means more wind exposure. We use heavier-gauge aluminum or copper on these edges because thin steel lifts in canyon gusts.
Homes near the canyon mouth take wind-driven rain at a steep angle, so we pay extra attention to the rake edge laps and fasteners.
Older tile and shingle roofs here need the drip edge tucked correctly under the tile course. We lift and reset tiles rather than break them.
Mid-century ranches with wide eaves are common here. The drip edge on these roofs is long, so repairs often cover 40 to 60 linear feet in one visit.
Local Considerations
Canyon wind gusts off the San Gabriel foothills
Lifts poorly fastened drip edge and tears sealant joints. We fasten every 12 inches and use heavier-gauge metal on exposed rakes.
Afternoon sun on west-facing rakes
Dries out butyl tape and roofing cement within a few seasons. We switch to polyurethane sealant that handles the temperature swings better.
Older wood fascia on pre-1980 homes
Rot spreads fast once water gets behind the edge. We check the fascia and quote carpentry before installing new metal.
Winter storm season from November through March
The first big storm finds every failed edge. We book edge inspections in October and November so repairs are done before the rain hits.
Lifted Drip Edge On A West Altadena Ranch
A windstorm lifted about 30 feet of drip edge along the west rake, and the homeowner found water stains on the attic sheathing after the next rain. The old sealant was cracked and the metal was fastened with only a few nails per section.
We replaced the full 30-foot section with new galvanized steel, fastened every 12 inches and sealed with polyurethane. The hose test ran 15 minutes with no moisture on the attic side, and the repair came in at $420.
Maintenance & Follow-up
Check the rake edge each fall before the first storm. If you see lifted metal or cracked sealant, call us before the rain starts.
The drip edge on this home had rusted through and was staining the fascia with orange streaks. Paint was peeling in long strips, and the homeowner had already repainted once without fixing the source.
We replaced 45 feet of corroded steel with heavier-gauge aluminum, treated the fascia and resealed the laps. Total job was $650 and took about four hours. The next storm left the fascia dry.
Maintenance & Follow-up
Repaint the fascia within a season of the repair so the wood stays sealed. We check the edge on every annual roof inspection.
This Christmas Tree Lane bungalow was built without drip edge, so water ran straight down the fascia and into the foundation planting. The sheathing edge stayed wet and the wood fascia had started to soften in two spots.
We fabricated custom drip edge on a flashing brake to match the original roof profile, installed it with a 2-inch lap, and sealed every joint. The repair covered 60 linear feet and cost $580, and the fascia has stayed dry through two winters.
Maintenance & Follow-up
Older homes without original drip edge should have the new metal checked once a year. We include it in our annual flashing inspection.
Frequently Asked Questions About Drip Edge Flashing Repair
Have questions? We have answers. If you don't see your question here, feel free to contact us.
Call UsHow much does drip edge flashing repair cost in Altadena CA?
Most drip edge flashing repair in Altadena, California runs $180 to $650 in 2026, depending on linear feet, metal type and whether the decking or fascia is damaged. A small reseal is usually under $250. A full 60-foot elevation replacement with new galvanized steel lands around $450 to $650. If carpentry is needed, add $200 to $800.
Why is my drip edge flashing leaking in Altadena, California?
The three most common causes are cracked sealant at the laps, fasteners that pulled loose in canyon wind, and metal that was installed with the wrong lap direction at the eave or rake. Altadena's sun dries out old butyl tape and roofing cement within a few seasons, which opens the joint. We inspect the edge and the attic side to confirm the source before we quote the repair.
Can you fix drip edge flashing leaks in Altadena?
Yes. We repair drip edge leaks on shingle, tile and flat roofs across Altadena, and most jobs finish in a single visit of two to four hours. We remove the failed section, check the deck, install new metal with a 2-inch lap and fasteners every 12 inches, then run a 10 to 15 minute hose test. You get photos and a 5-year workmanship warranty.
Do you offer drip edge flashing fix near me in Altadena?
We serve all of Altadena, including West Altadena, East Altadena, Loma Alta, Rubio Canyon and the Christmas Tree Lane area, plus ZIP codes 91001, 91003 and 91104. Most drip edge flashing fix near me calls get on the schedule within 24 to 48 hours. During storm season we hold slots open for emergency drip edge flashing fix Altadena requests.
Licensed, Insured And Local To Altadena
Certifications
Customer Reviews
Our drip edge lifted along the whole west rake after that windstorm in November. Hometown Roof Protectors came out two days later, replaced 30 feet of metal, and ran a hose test before they left. No more stains on the attic sheathing. Fair price and they cleaned up every nail.
We had rust streaks on the fascia and peeling paint for two years. Turned out the drip edge was the source. They replaced 45 feet with aluminum, treated the fascia, and the paint has held up since. Took about four hours and the price matched the quote.
Our 1920s bungalow near Christmas Tree Lane never had drip edge. They fabricated custom metal on site to match the roof line and installed 60 feet. Two winters later, the fascia is dry. They also checked our step flashing and kickouts while they were up there.
Called about a drip edge flashing fix near me in Altadena and got on the schedule the next day. The technician showed me photos of the failed section and explained why the old sealant cracked. Repair was under $400 and the 5-year warranty gave me confidence.
Related Roof Flashing Services In Altadena
Explore our other professional services
Roof Flashing Repair
Drip edge is one part of the flashing system. If your leak is at a wall, valley or penetration, our roof flashing repair service covers the full picture across Altadena.
Roof Flashing RepairRoof Leak Repair
When a drip edge leak has already traveled into the attic or a ceiling, we trace it back to the source and repair the roof leak before it spreads further.
Roof Leak RepairChimney Flashing Repair
Leaking chimney flashing often shows up at the same time as a failed drip edge. We repair both in one visit so you are not paying for two trips.
Chimney Flashing RepairSkylight Flashing Repair
Water intrusion at skylights and drip edge failures share the same wind-driven rain problem in Altadena. We seal both to NRCA standards.
Skylight Flashing RepairVent Pipe Flashing Repair
Vent pipe boot failure is one of the most common roof leaks in Altadena. We replace the boot and check the nearby drip edge while we are up there.
Vent Pipe Flashing RepairValley Flashing Repair
Valleys take the heaviest water flow on any roof. If your valley flashing is failing, we repair it alongside the edge work for one clean scope.
Valley Flashing RepairStep Flashing Repair
Improper step flashing installation lets water into walls at the same rate as a bad drip edge. We repair both to keep the whole roof edge watertight.
Step Flashing RepairCounter Flashing Repair
Loose counter flashing at chimneys and walls lets water behind the masonry. We reseat and reseal it as part of a full flashing repair.
Counter Flashing RepairKickout Flashing Repair
Missing kickout flashing is common on older Altadena homes and causes the same wall staining as a failed drip edge. We fabricate and install new kickouts on site.
Kickout Flashing RepairWall Flashing Repair
Where a roof meets a wall, wall flashing does the same job as drip edge at a different angle. We repair both so water has nowhere to sit.
Wall Flashing RepairRoof Flashing Replacement
When the metal is too far gone to repair, we replace the full flashing system with new galvanized steel, aluminum or copper built for Altadena weather.
Roof Flashing ReplacementEmergency Roof Flashing Repair
Storm-driven edge failures can flood a wall in hours. We hold emergency slots during Altadena storm season and can usually respond within 24 hours.
Emergency Roof Flashing RepairRoof Flashing Inspection
An annual flashing inspection catches cracked sealant and loose fasteners before they leak. We check the drip edge, step flashing, kickouts and boots in one visit.
Roof Flashing InspectionRoof Flashing Maintenance
Resealing laps and tightening fasteners every year or two keeps drip edge working. Our maintenance visits cover the whole flashing system.
Roof Flashing MaintenanceRoof Flashing Sealing
When the metal is sound but the sealant has failed, resealing is the fastest fix. We use polyurethane sealant rated for Altadena's temperature swings.
Roof Flashing SealingMetal Roof Flashing Repair
Metal roofs need edge details that account for expansion and contraction. We repair drip edge and flashing on standing seam and metal panel roofs.
Metal Roof Flashing RepairShingle Roof Flashing Repair
Shingle roofs are the most common in Altadena, and the drip edge detail at the eave and rake is where most leaks start. We repair both.
Shingle Roof Flashing RepairTile Roof Flashing Repair
Tile roofs need the drip edge tucked correctly under the tile course. We lift and reset tiles without breaking them during the repair.
Tile Roof Flashing RepairFlat Roof Flashing Repair
Flat roofs use modified bitumen and EPDM at the edges. We repair drip edge and perimeter flashing on both systems.
Flat Roof Flashing RepairCommercial Roof Flashing Repair
We handle drip edge and perimeter flashing on Altadena commercial buildings, including TPO and modified bitumen systems.
Commercial Roof Flashing RepairResidential Roof Flashing Repair
From bungalows near Christmas Tree Lane to newer builds in La Viña, we repair residential flashing across Altadena.
Residential Roof Flashing RepairStorm Damage Flashing Repair
After a windstorm, we inspect the full edge, replace lifted metal and document the damage for insurance if needed.
Storm Damage Flashing RepairRoof Flashing Installation
New roof or re-roof? We install drip edge, step flashing and kickouts to code so the edge detail is right from day one.
Roof Flashing InstallationCustom Flashing Fabrication
Older Altadena homes often need custom profiles. We fabricate drip edge and flashing on a brake to match the original roof line.
Custom Flashing FabricationRoof Flashing Leak Detection
Not sure where the water is coming in? We trace the leak from the attic side and confirm the source before quoting the repair.
Roof Flashing Leak DetectionGutter Flashing Repair
Gutter and drip edge work together at the eave. We repair both so water leaves the roof cleanly instead of backing up.
Gutter Flashing RepairRoof Flashing Waterproofing
We seal laps and joints with polyurethane and butyl tape to waterproof the edge against wind-driven rain.
Roof Flashing WaterproofingRoof Flashing Repair Near Me
If you are searching for roof flashing repair near me in Altadena, we serve the whole city and most jobs get scheduled within 24 to 48 hours.
Roof Flashing Repair Near MeBook Your Drip Edge Flashing Repair Altadena CA Today
A lifted drip edge gets worse with every storm. We are a licensed C-39 roofing contractor serving Altadena since 2020, and most repairs finish in one visit with a 5-year workmanship warranty. Call us and we will get eyes on your roof within 24 to 48 hours.